Best free roulette tracker tools 2025-2028

Hiya Having some issues with my grow, it just keeps throwing curved balls at me. Basically - i had what looked like nitrogen toxicity. So she had a 2.5 flush in just pHd water, she looked pretty bad towards the end of that. Ppm stayed the same, i thought it might rise as she puked out the excess N. About 6 hours ago she got a new tank with 450ppm of AH Bloom (0-5-5) specially chose that as it had no N. 450 seemed like a reasonable strength feed after a flush. And now, in 6 hours pH 5.9 risen... Nute issues DWC February 29, 2020 at 03:09PM Read more about this fix

I've read and heard others say just enough for the roots to touch. I'm using 5 gallon buckets with about 3 gallons of water. I change the water weekly and when I do I notice my plants damn near drink it all leaving hardly in the buckets. I'm on week two of flowering and used this amount the whole time. I'm just worried about getting root rot. As of now my roots are massive and white and doing fine. So should I lower the level of water and change more often or leave it alone? February 28, 2020 at 10:13AM Read more about this fix

Hi. I've been lurking on this board for a few months and finally decided to post. I'm just about done killing of my second batch of plants I'm grateful for the experience and have learned a lot.... Most of my problems have stemmed from oscillating on grow systems. Thus far bubbleponics has worked the best (and loudest) but I have also tried fogponics. I would like try is again but there seems to be a lack of info out there. Can anyone point me in the right directions or should I just... What Ever Happened to Fogponics

I'm having trouble with my res its 220 litre the ph keeps going up I set at 5.8 the next day its 6.3 or more an goes up more the next day I have a water pump an air pump in there iv taken the air stone off the air pump but still doing it any ideas for help please thanks

I'm having trouble with my res its 220 litre the ph keeps going up I set at 5.8 the next day its 6.3 or more an goes up more the next day I have a water pump an air pump in there iv taken the air stone off the air pump but still doing it any ideas for help please thanks February 26, 2020 at 09:17PM Read more about this fix

Hi. I've been lurking on this board for a few months and finally decided to post. I'm just about done killing of my second batch of plants I'm grateful for the experience and have learned a lot.... Most of my problems have stemmed from oscillating on grow systems. Thus far bubbleponics has worked the best (and loudest) but I have also tried fogponics. I would like try is again but there seems to be a lack of info out there. Can anyone point me in the right directions or should I just... What Ever Happened to Fogponics February 26, 2020 at 01:42PM Read more about this fix

So i have to decide and i cant so cmon yall Wilma xl 180l with 8 net pots dropped in the rez 1000lph feed lines running halo drips or waterfall return Helia v60 6x 6inch air disks Or 4 really useful boxes and a controll res Plumbed with 63mm returns at base front n back. And 4000lph in res on spray bars Helia v60 4x6inch airstones and res with a air diffuser block Eitherway 2 600watts on top in my 2.4x1.2 tent Im hitting 1.2gpw in my wilma. Roots cause me no issues other than when big... modded wilma vs rdwc

looking for a thread by Ogre Seeker? DIY controller bucket. looking for the simplest yet DEPENDABLE controller bucket system. going to be used in an upstairs so overfill or leakage needs to be avoided lol does anyone have alink or know where links to this build are at? and yes i searched first to no avail. found one to an icmag Kryptonite but heard there was a better one out by ogreseeker??? here???????? sTaY lIfTed! February 26, 2020 at 02:31AM Read more about this fix

I know this was discussed a lot but just wondering if anything changed ? So my TAP readings are PPM 200 PH 6.8 I know it has a chlorine and chloramine so i was thinking to let it outside for 24 hr most of chlorine will evaporate and use Campden tablets to remove chloramine or maybe use something like this ? https://www.amazon.com/gp/product/B07Y1D6YFQ/ref=ask_ql_qh_dp_hza Main reasons im asking 1. Filter above gives u 2GPM vs my RODI 5 GPH 2. no wasted water... TAP water for RDWC question

I used to pull 3lbs consistently in my 8x4 space, under 2 x 1000w hps. 4 week veg. Now im switching to COB (1300w) and 2X 4 by 4 flood tables. I was thinking i should easily pull the same weight or better once i get dialled in. In fact, i figure i should be able to do 2lbs per table. But... how to do it? I have a 24 plant count limit on my med lic. Another restriction is that i have 71 inches total height in the room when my lights are all the way up. So take off 22 in for light distance... How get 2lb per flood table? February 24, 2020 at 03:07AM Read more about this fix

Sup everyone, welcome to thread that will contain the journey of this LPA build and setup and prob its inaugural run. Ive been wanting to try aero or rdwc for a bit, i figure a nice winter project isnt such a bad idea. The plan: i will run 4 totes(1 plant per) off a 40g res, feeding a manifold thats connected to all tote sprayers. Runoff will be drained out the bottom and back into the res. Materials : 4 x 27gallon Rectangular totes, 29"x20"x15" 1 x 40 gallon low rise reservoir 1 x 800... Low Pressure Aero build...it has begun!

Hey all, it's my first post here and I am needing some input on my current (1st) grow. I have scoured and read and taken in so much info but would like to get some feedback as well. Currently I have 4 single bucket dwc's going. 5g buckets with slightly over 3g of water in each which puts my water level to about 2" below netpots. I had 4g in each until I started seeing first roots break through the bottom and then I lowered to 3g. (2) 6" long airstones in each bucket which I feel like is... Newbie DWC! Root rot question!

Hi guys, I have some weird brown spots on some of my leafs on 1 or 2 plants out of 12. so i cant figure out what it could be, if they all had it ok but why only 2 to 3 plants showing this? also what the heck is this ? RDWC setup with ec of 1.7 ph 5.9 water temp 63 and using Southern AG February 21, 2020 at 07:42PM Read more about this fix

I know this was discussed a lot but just wondering if anything changed ? So my TAP readings are PPM 200 PH 6.8 I know it has a chlorine and chloramine so i was thinking to let it outside for 24 hr most of chlorine will evaporate and use Campden tablets to remove chloramine or maybe use something like this ? https://www.amazon.com/gp/product/B07Y1D6YFQ/ref=ask_ql_qh_dp_hza Main reasons im asking 1. Filter above gives u 2GPM vs my RODI 5 GPH 2. no wasted water... TAP water for RDWC question February 21, 2020 at 06:36PM Read more about this fix

Hey people lets talk about cloning temperatures...some say 70 some say 80. When I take clones using Rapid Rooters and a Dome... I get quicker roots in summertime when the temp is 80... in the wintertime the temp drops down to around 70 and the clones take twice as long to root. I have the ez cloner its running a temp of 78*F.... people are saying you want to be at 70*F....WHY? Is it just because the slime monster and bacteria say away with the colder temps??? They have clonex clear rez... What is the proper water temperature for cloning using a cloning machine

Was wondering what you guys used for large scale growing on air pumps. I’ve got grow rooms that I’m setting up that will be 50 buckets and 100 bucket rooms. February 20, 2020 at 11:30PM Read more about this fix

I have some new seeds that I want to get going in a hydro setup. I usually do soil to start but trying to get them going quick. I can do dwc or use my aero cloner February 20, 2020 at 03:30PM Read more about this fix

Curious about using PS in your reservoir. I run ebb and flow and start with clones. Should I add the potassium silicate right in the beginning when I first put the clones on the table? And then keep adding it until week 6 of flower? This bottle I have of DNF nutes doesn't really give me any feed schedule for the stuff other than add 1/4tsp per litre. Also I heard it is best to mix it in a bit of warm water then add it to the reservoir first before adding your nutes. Also that it will... Using potassium silicate in your reservoir

Curious about using PS in your reservoir. I run ebb and flow and start with clones. Should I add the potassium silicate right in the beginning when I first put the clones on the table? And then keep adding it until week 6 of flower? This bottle I have of DNF nutes doesn't really give me any feed schedule for the stuff other than add 1/4tsp per litre. Also I heard it is best to mix it in a bit of warm water then add it to the reservoir first before adding your nutes. Also that it will... Using potassium silicate in your reservoir February 20, 2020 at 03:23AM Read more about this fix

Hey all, it's my first post here and I am needing some input on my current (1st) grow. I have scoured and read and taken in so much info but would like to get some feedback as well. Currently I have 4 single bucket dwc's going. 5g buckets with slightly over 3g of water in each which puts my water level to about 2" below netpots. I had 4g in each until I started seeing first roots break through the bottom and then I lowered to 3g. (2) 6" long airstones in each bucket which I feel like is... Newbie DWC! Root rot question! February 20, 2020 at 01:14AM Read more about this fix

Hello everyone! I was pretty tired of having to fill up my buckets to root level so I designed this with General Hydroponics' WaterFarm as inspiration! Uses a 3D Printed Venturi Pump. Netpot Drip Adapter is here: https://www.thingiverse.com/thing:4170286 Venturi Pump is Here: https://www.thingiverse.com/thing:1749618

Hello everyone! I was pretty tired of having to fill up my buckets to root level so I designed this with General Hydroponics' WaterFarm as inspiration! Uses a 3D Printed Venturi Pump. Netpot Drip Adapter is here: https://www.thingiverse.com/thing:4170286 Venturi Pump is Here: https://www.thingiverse.com/thing:1749618 February 19, 2020 at 03:26AM Read more about this fix

This will be my second indoor grow, my last one was a single DWC and now I'm upgrading to a 2'x4' tent, I'll be growing a scrog, number of plants TBD. My original plan was to start off with 1 Rubbermaid eventually transfer to 3 Rubbermaid bins once the scrog fills up, each one as their own DWC, since they will pretty much exactly fill up my floor space. Ive got a single hydroform 15lpm air pump, but that didn't seem like it would be sufficient. Now instead of buying a larger air pump I'm... Another noob setup post February 17, 2020 at 03:21PM Read more about this fix

Hi everyone I m wondering if this curling because of too much light ? or some kind of deficiency , mainly the new growth is curling Friend of mine suggested to lower the intensity and i did i have HLG Rspec 24 inch above at 230 watts i lowered it to 195 watts RDWC PPM – 820 Temp – 73 PH –5.9 im using Lucas FLoranova and silica the are on 15th day of veg im adding 50 ml h2o2 every 4 days diluted in 350 ml rez water and just added 20 ml calmag

I need some advice. I have built my low pressure aeroponics setup, and everything seems to work alright...except the fountain pump makes a hell of a noise. The system is basically two containers stacked. Pump is in the bottom with pvc pipe running vertically up. There is an off-take to the side for draining with a valve, and the main line continues to run past that to the top container where it splits into horizontal pvc with low pressure sprayers. Only the off-take and valve are glued, the... Low Pressure Aero Pump Noise... February 17, 2020 at 08:42AM Read more about this fix

All right! Hydroponics is what I know, and hydroponics is the way I grow! This forum will be great, we can discuss anything hydro. No dirtbags here, We haul water! We can compare the different nutrient salts, and all of the additives. Plus the kinds of soilless media and what irrigation system is best for each. And of course, pH and TDS measuring equipment, feeding and flushing, etc. And all the while, we'll make fun of those guys hauling big bags of dirt! :blsmoke... Hydroponics February 17, 2020 at 03:21AM Read more about this fix

Hello all, So I got some root rot few days ago and someone on this forum suggested i use Southern AG. Looks like they are recovering right? Should i be worried about the rot on some parts of the roots or just let it be and it will go away by itself? not sure what to do here? I looked at the roots today (see pics ) and looks like im getting some really really white healthy roots coming out of a few of them. This is leading me to believe that the problem is going away. Now on top of this i... Root rot + Southern AG, recovering? and nitrogen deficiency February 17, 2020 at 01:28AM Read more about this fix

i have a 4x4 tray drain and fill system goin with a 600w hps light above the table. how many plants can i grow at one time? February 16, 2020 at 04:55PM Read more about this fix

Hi everyone I m wondering if this curling because of too much light ? or some kind of deficiency , mainly the new growth is curling Friend of mine suggested to lower the intensity and i did i have HLG Rspec 24 inch above at 230 watts i lowered it to 195 watts RDWC PPM – 820 Temp – 73 PH –5.9 im using Lucas FLoranova and silica the are on 15th day of veg im adding 50 ml h2o2 every 4 days diluted in 350 ml rez water and just added 20 ml calmag February 16, 2020 at 08:51AM Read more about this fix

Hey people lets talk about cloning temperatures...some say 70 some say 80. When I take clones using Rapid Rooters and a Dome... I get quicker roots in summertime when the temp is 80... in the wintertime the temp drops down to around 70 and the clones take twice as long to root. I have the ez cloner its running a temp of 78*F.... people are saying you want to be at 70*F....WHY? Is it just because the slime monster and bacteria say away with the colder temps??? They have clonex clear rez... What is the proper water temperature for cloning using a cloning machine

Hey people lets talk about cloning temperatures...some say 70 some say 80. When I take clones using Rapid Rooters and a Dome... I get quicker roots in summertime when the temp is 80... in the wintertime the temp drops down to around 70 and the clones take twice as long to root. I have the ez cloner its running a temp of 78*F.... people are saying you want to be at 70*F....WHY? Is it just because the slime monster and bacteria say away with the colder temps??? They have clonex clear rez... What is the proper water temperature for cloning using a cloning machine February 14, 2020 at 10:41PM Read more about this fix

Total stretch 2 inches... Anyone else have that? Know why? All the horror stories I read but I never noticed anyone stating theirs didn't move in the 3 weeks... Some pics.. red line was pre flip.. besides that... Looks like I'll get at least 2 pounds off this one plant. Jokes aside I'm looking forward to seeing this fatten up, the node length is tiny which is why the stretch was small.

Im about to set up a flood and drain table in a 3x4 tent the table will be 3x3. My question is should i flower a bunch of clones in it or just 2 plants and let them grow big? Im looking to maximize yield. But my plant count is only 24. February 13, 2020 at 04:38PM Read more about this fix

So i have to decide and i cant so cmon yall Wilma xl 180l with 8 net pots dropped in the rez 1000lph feed lines running halo drips or waterfall return Helia v60 6x 6inch air disks Or 4 really useful boxes and a controll res Plumbed with 63mm returns at base front n back. And 4000lph in res on spray bars Helia v60 4x6inch airstones and res with a air diffuser block Eitherway 2 600watts on top in my 2.4x1.2 tent Im hitting 1.2gpw in my wilma. Roots cause me no issues other than when big... modded wilma vs rdwc February 13, 2020 at 10:41AM Read more about this fix

I recently switched from GH Flora series to Jack's 321 after watching a GreenGeene's Garden video. If I ran GH over 1.8 EC on a 3ft plant in flower, it would start to show a little burning. With Jack's I'm starting at 2.2 EC from rooted clone and have no burn. Why is that? February 13, 2020 at 09:54AM Read more about this fix

I’ve seen this asked many times with most answers being just get bigger piping but these buckets i can’t get any of the bulkheads or whatever they are out so id rather attempt to fix them remove them all. A few have gotten roots stuck and caused some water overflow, which i don’t have the best preventive measure for as I am not in a basement and flodding is the worst thing that could happen lol. But besides being diligent and... Any way to add mesh?

I’ve seen this asked many times with most answers being just get bigger piping but these buckets i can’t get any of the bulkheads or whatever they are out so id rather attempt to fix them remove them all. A few have gotten roots stuck and caused some water overflow, which i don’t have the best preventive measure for as I am not in a basement and flodding is the worst thing that could happen lol. But besides being diligent and... Any way to add mesh? February 12, 2020 at 07:41PM Read more about this fix

Thanks to anyone taking the time to help me with this. To not waste time I’m just going to throw it out there. I just moved to hydro a few months back, after growing soil for a long time, so I’m not a stranger to to the field. I will explain my situation as I know how frustrating it can be when broad questions are asked and when 99% of issues can be caused by many variables from one’s grow to another’s. Current setup. DWC and an NFT- type system. Both systems cause what I’m going to show... Leaf diagnosis help - possible lockout?

Thanks to anyone taking the time to help me with this. To not waste time I’m just going to throw it out there. I just moved to hydro a few months back, after growing soil for a long time, so I’m not a stranger to to the field. I will explain my situation as I know how frustrating it can be when broad questions are asked and when 99% of issues can be caused by many variables from one’s grow to another’s. Current setup. DWC and an NFT- type system. Both systems cause what I’m going to show... Leaf diagnosis help - possible lockout? February 12, 2020 at 03:30AM Read more about this fix

Hey folks , I am hoping someone here has done this or has an idea. This is my first time mixing and matching in my current culture 6 site. One is going to be ready about 3 or so weeks ahead of the rest and I am curious how can I flush her for a few days? I do not think I can take her out as she is pretty well trained and laying almost flat on the trellis. I do have extra buckets not in use on the side and am envisioning I will HAVE to maneuver her out some way into her own bucket (I do have... How to flush a single plant in Current Culture setup February 11, 2020 at 03:55PM Read more about this fix

Howdy everyone. I've been lurking here a long time, and only recently finally registered. I've read a ton of threads with differing opinions (so, my mind boggles), and along the way have come up with a few questions that weren't addressed, found in topics I liked. Anybody who might elaborate on this -- in theory or practice -- it would be appreciated. These are not really start-up questions in some cases, just stuff I'm wondering about. Background: I am turning a bedroom (11'w x 12l' x... I have questions. Filling in knowledge gaps. February 10, 2020 at 10:20PM Read more about this fix

Sup everyone, welcome to thread that will contain the journey of this LPA build and setup and prob its inaugural run. Ive been wanting to try aero or rdwc for a bit, i figure a nice winter project isnt such a bad idea. The plan: i will run 4 totes(1 plant per) off a 40g res, feeding a manifold thats connected to all tote sprayers. Runoff will be drained out the bottom and back into the res. Materials : 4 x 27gallon Rectangular totes, 29"x20"x15" 1 x 40 gallon low rise reservoir 1 x 800... Low Pressure Aero build...it has begun!

Anyone here do autos in DWC? I’m running my first Photoperiod DWC buckets and was wanting to possibly move to autos in the future for a more flexible perpetual harvest. Any differences between DWC for photos? Any tips or pointers? February 10, 2020 at 02:01AM Read more about this fix

Hi everyone , im new here so no yelling This is my first grow i got clones from friend of mine , he cloned them from flowering stage and i guess messed up cycle and clones started to flower (it had tiny buds and have a strong smell )while being 7 inch tall. 1st week everything was i was trying to flip them back to veg ,now im on a 2nd week and ph started to raise slowly 6.0-6.1-6.2 in course of 3 days 8*4 tent PPM 370 Temp 74 Rez Tent temp 74 PH -6.2 Im using floranova bloom with some... PH rises 0.1 every 24 hours

Got a letter today stating that starting in a week or so, the city will be replacing the water main on the street I live on. No estimated completion date or anything. I typically fill my systems straight from the tap with a garden hose and I am assuming there will be some level of contamination from the work. How do you guys think I should handle this, or do you think im overreacting? I have a collapsible 200 gallon holding tank available. I was thinking id just fill that sometime next... Water main being replaced soon. Should I worry? February 09, 2020 at 01:32AM Read more about this fix

Hi everyone , im new here so no yelling This is my first grow i got clones from friend of mine , he cloned them from flowering stage and i guess messed up cycle and clones started to flower (it had tiny buds and have a strong smell )while being 7 inch tall. 1st week everything was i was trying to flip them back to veg ,now im on a 2nd week and ph started to raise slowly 6.0-6.1-6.2 in course of 3 days 8*4 tent PPM 370 Temp 74 Rez Tent temp 74 PH -6.2 Im using floranova bloom with some... PH rises 0.1 every 24 hours February 08, 2020 at 08:13PM Read more about this fix

My 1st time growing so not sure when is the right time to swap them to flowering. I put the clones in the system back on Jan 8th about 33 days ago. Dont want to risk having them overgrow during flowering and me running out of space in the tent lol. maximum space i have from the top of the bucket to the top of the tent that the light can be is 53" now if i take out another 10" for the space between the buds and the light that leaves me 43" and my plants now are about 17 to 20" I have... need some advice re swapping to flowering!

My 1st time growing so not sure when is the right time to swap them to flowering. I put the clones in the system back on Jan 8th about 33 days ago. Dont want to risk having them overgrow during flowering and me running out of space in the tent lol. maximum space i have from the top of the bucket to the top of the tent that the light can be is 53" now if i take out another 10" for the space between the buds and the light that leaves me 43" and my plants now are about 17 to 20" I have... need some advice re swapping to flowering! February 07, 2020 at 06:50AM Read more about this fix

Ok, I have been using PH Down Dry to adjust my tank. I am wanting to flush for awhile and that will put me low on that to make a flush tank and then make a nute tank back up. I have a spa and use a product called PH minus that contains 93.3% sodium bisulfate and 6.7 % sodium sulfate. Is that spa PH down save for hydro? February 06, 2020 at 04:30PM Read more about this fix

Hey guys.. so in the past 7 weeks I've managed to kill a seedling, a month old plant and it looks like I'm about to kill my 7 week old flowering auto. I've got a 10 day old seedling who is doing ok (for the moment) but I'm feeling less than confident. I just can't get my system in order! So, here's my basic set up: Everything has been an auto so far. DWC 6 gallon buckets (homemade from food grade buckets), wrapped in foil tape. I have 4 air stones in each bucket pushing air, hydroton with... I really need some hydro help... feeling super discouraged and confused!

has any1 used this and were can i get this shit and the chick that was talking about it was fucking hot were can i get her aswell ? February 06, 2020 at 01:20AM Read more about this fix

Been putting some thoughts into Octopots, there are a couple guys using them in local facebook grow groups that seem to be getting good results. Who all has grown with octopots on here, and what did you think? February 06, 2020 at 01:42AM Read more about this fix

Hey guys.. so in the past 7 weeks I've managed to kill a seedling, a month old plant and it looks like I'm about to kill my 7 week old flowering auto. I've got a 10 day old seedling who is doing ok (for the moment) but I'm feeling less than confident. I just can't get my system in order! So, here's my basic set up: Everything has been an auto so far. DWC 6 gallon buckets (homemade from food grade buckets), wrapped in foil tape. I have 4 air stones in each bucket pushing air, hydroton with... I really need some hydro help... feeling super discouraged and confused! February 06, 2020 at 12:54AM Read more about this fix

So I've never done hydro and my neighbor is starting his first seedlings in rockwool, just 2 very quick questions, 1: how deep in the rockwool should the seed be sown? These are the round rockwool pods that open up from the side it's not a hole that goes down. 2: how high should the water in the tray be? Should it come right up to the seed or just enough to soak the rockwool? Any help would be appreciated. February 05, 2020 at 10:42PM Read more about this fix

I'm possibly thinking of switching to RDWC pretty soon.. I don't want to deal with coco anymore. I currently have a flower room that is 7x5. Would doing a 8 site rdwc in 5 gallon buckets be over kill? How would totes go compared to buckets? HD/LOWES currently have 27gallon totes for like $9 bucks.. I could do 2 plants in one and get like 4 totes? February 05, 2020 at 09:25PM Read more about this fix

I was planning on using Hunter for the irrigation controller + pump start relay, but might choose TrolMaster's Aqua-x since it can control multiple pumps/devices, so I could control the veg room too. Not sure yet, but is the design itself good? Is there anything I'm missing? February 05, 2020 at 07:22PM Read more about this fix

Wondering if anyone has tried to start seeds using an aero cloner - no dirt/perlite/rockwool used. My thoughts are... 1. Start the seeds in a paper towel 2. Once the seeds crack & have the little white tap root showing gently place them low in a neoprene disk & in the cloner 3. Fill cloner with pH5.8 water and wait for the magic to happen Think it'll work???

Wondering if anyone has tried to start seeds using an aero cloner - no dirt/perlite/rockwool used. My thoughts are... 1. Start the seeds in a paper towel 2. Once the seeds crack & have the little white tap root showing gently place them low in a neoprene disk & in the cloner 3. Fill cloner with pH5.8 water and wait for the magic to happen Think it'll work??? February 05, 2020 at 06:00AM Read more about this fix

hey guys plants are over 2 months old went through hell n back just getting these started. the roots no matter what dont want to go in the water. they pull out easy n are a lil slimey. i just killed this plant n im tempted to get rid of the other 2 n start over. February 04, 2020 at 11:08PM Read more about this fix

Sup everyone, welcome to thread that will contain the journey of this LPA build and setup and prob its inaugural run. Ive been wanting to try aero or rdwc for a bit, i figure a nice winter project isnt such a bad idea. The plan: i will run 4 totes(1 plant per) off a 40g res, feeding a manifold thats connected to all tote sprayers. Runoff will be drained out the bottom and back into the res. Materials : 4 x 27gallon Rectangular totes, 29"x20"x15" 1 x 40 gallon low rise reservoir 1 x 800... Low Pressure Aero build...it has begun!

Ok hi peeps! man ... have had lots of heat probs. from my new LUMATEK 600W HPS in my original cab so..... I've swapped cupboards with my wife and now have a better sized cupboard in which to grow. However I do have my work cut out for me, so bare with me this will be one hell of a cool thread from start to finish. SO without further a due I am going to crack on, all thoughts comments and surgestions welcome as long as its relevant its all good - STELTHY February 03, 2020 at 10:43PM Read more about this fix

Hi all, I have a question or two, regarding the CANNA GROW GUIDES.. I understand how to fill in and use the guides..but when should I ~ if at all change from "LIGHT FEEDING CHART" to the "MEDIUM FEED CHART". . and then finally from medium to "HEAVY FEED CHART"...??? Does it depend on what you are growing , strain, size , age..etc.. and should I pay any attention to the light medium and heavy varient if I am already checking the EC is in range...? Also CANNAS PK 13/14 ... Does anyone know... CANNA GROW GUIDE QUESTIONS February 03, 2020 at 10:07PM Read more about this fix

Currently am vegging just in rockwoool cubes and hydroton in essentially litter boxes. 5 plants to one. Vegging for like 6 weeks. then moving to RDWC. I feel like I could be doing a better veg system. i’ve seen others after a 5 week veg seem a lot bigger, obviously many favors but Infeel the roots almost get root bound sometimes? some when they move to the buckets explode with growth while others barely explode at all yet looked very similar root wise and size leaving veg. Should i... Best way to Veg prior to flowering in RDWC February 03, 2020 at 08:58PM Read more about this fix

Ok, so it's my first grow and I have managed to make just about every mistake in the book. This little auto, 2vast 2fast, is somehow still alive in spite of me... although she's not looking too pretty. So, here is where I am at. She is being grown in a dwc 6 gallon bucket under a 300 watt blurple. (I have a new light on order, but it's not arrived yet.) Light is about 18" from my plant. She's 6 weeks old and quite stunted. Nevertheless, she's starting to preflower. Temperature range... This poor plant. I'm the worst mom. Any advice? February 03, 2020 at 02:40PM Read more about this fix

My pH buffer solutions for calibration of my meters are out of date; I see no precipitation of salts in the bottles; are they still good? I have VWR brand 4, 7,and 10. The neutral yellow 7 buffer solution looks almost clear now, but the red 4 and blue 10 look the same as when new (still blue and red). I think the color dyes are the only things that can actually degrade. When I check the neutral against a newer but still expired 7 from cole parmer it's still within 0.1 pH unit. I assume... Expiration date on pH buffers February 02, 2020 at 09:18PM Read more about this fix

Anyone use a Nearpow Timer? Does anyone know of a timer the allows every other day cycles? TY, Alta February 02, 2020 at 10:06AM Read more about this fix

hey guys, ill post a few pics but had a few questions about what defficiency i gots. and my roots arent growing into the water their growing like outwards from the netpot. before i remember the roots just loved being in the water from.another grow. heres some info 25 gal system rdwc gh flora trio nutes ro water cal mag bleach 10ml water temp is 65-69f air temp been 60f-83f ppm is around 900 and ph was 5.3. ive since lowered ppm to 680 and ph is now 5.8. plants just look sad, not sure... plants lookin awful weird roots

I added about 2ml per gallon of 35% h2o2 to my res but i did it a little faster then i normally do and i just noticed most of their leafs are curled and basically looked burned from the inside. The h2o2 is the only thing i did today and everything looked amazing the morning. Will they recover or is it game over for my them is it possible it could of been from the heat wave we had today? its outdoors in a greenhouse and the temps have been about 60 to 70 but today it reached about... Can this be from the h2o2 i added today??? February 02, 2020 at 06:33AM Read more about this fix

hey guys, ill post a few pics but had a few questions about what defficiency i gots. and my roots arent growing into the water their growing like outwards from the netpot. before i remember the roots just loved being in the water from.another grow. heres some info 25 gal system rdwc gh flora trio nutes ro water cal mag bleach 10ml water temp is 65-69f air temp been 60f-83f ppm is around 900 and ph was 5.3. ive since lowered ppm to 680 and ph is now 5.8. plants just look sad, not sure... plants lookin awful weird roots February 02, 2020 at 03:07AM Read more about this fix

Sup everyone, welcome to thread that will contain the journey of this LPA build and setup and prob its inaugural run. Ive been wanting to try aero or rdwc for a bit, i figure a nice winter project isnt such a bad idea. The plan: i will run 4 totes(1 plant per) off a 40g res, feeding a manifold thats connected to all tote sprayers. Runoff will be drained out the bottom and back into the res. Materials : 4 x 27gallon Rectangular totes, 29"x20"x15" 1 x 40 gallon low rise reservoir 1 x 800... Low Pressure Aero build...it has begun!